ifvh

3 Days

8 Scheduled Dates

3 Locations

$2,838.00 Incl. GST
$2,580.00 Excl. GST

Overview

This three-day course focuses on the ScreenOS features that are typically necessary in large-scale networks, including dynamic routing, virtual systems, traffic shaping, and high availability. Upon completing this course, students should be able to successfully install and configure a ScreenOS device. Students should also be able to verify that a ScreenOS device is interoperating in the network as desired. Through demonstrations and hands-on labs, students gain experience in configuring, testing, and troubleshooting these advanced features of ScreenOS software. This course is based on ScreenOS version 6.3r14.

Audience Profile

This course is intended for network engineers, network support personnel, and reseller support personnel.

Objectives

After successfully completing this course, you should be able to:

Configure virtual systems, including standard, IP-based, and transparent mode.

Configure dynamic routing protocols, including OSPF and Border Gateway Protocol (BGP).

Configure multicast operations, including Internet Group Management Protocol (IGMP) and Protocol Independent Multicast sparse mode (PIM SM).

Configure high availability in both static routing and dynamic routing environments.

Configure traffic shaping features.

Verify operations and troubleshoot all previous configurations.

Prerequisites

The following are the prerequisites for this course:

Completion of the Configuring Juniper Networks Firewall/IPsec VPN Products (CJFV) course or equivalent product experience

General networking knowledge, including an understanding of Ethernet, TCP/IP, and routing concepts.

Outline

  • Section 1 : Course Introduction
  • Section 2 : ScreenOS Basics Review
    Lessons
    • Concepts Review
    • Configuration Review
    • ScreenOS Basics Review
  • Section 3 : Interior Gateway Protocols
    Lessons
    • RIP Operations
    • OSPF Operations
    • OSPF Configuration
    • Verification and Troubleshooting
    • Route Redistribution
    • Route Optimization
    Labs
    • Configuring OSPF—Part 1
    • Configuring OSPF—Part 2
    • Configuring OSPF—Part 3
  • Section 4 : BGP
    Lessons
    • BGP Operations
    • EBGP Configuration
    • Verification and Troubleshooting
    • IBGP Configuration
    • BGP Connectivity
    Labs
    • Configuring BGP
  • Section 5 : Advanced Static Routing
    Lessons
    • Source-Based Routing
    • Policy-Based Routing
    • Destination Routing
    Labs
    • Configuring Advanced Static Routes
  • Section 6 : Multicast
    Lessons
    • Multicast Overview
    • IGMP Operations
    • IGMP Configuration
    • PIM SM Operations
    • PIM SM Configuration
    • Multicast Policies
    Labs
    • Configuring Multicast Support
  • Section 7 : Virtual Systems
    Lessons
    • Vsys Operations and Concepts
    • Configuring Vsys Using Interface Classification
    • Vsys Resource Management
    • Inter-Vsys Routing
    • Address Translation
    Labs
    • Configuring Virtual Systems—Part 1
    • Configuring Virtual Systems—Parts 2 and 3
    • Configuring Virtual Systems—Part 4
  • Section 8 : Redundancy
    Lessons
    • NSRP Terms and Concepts
    • Configuring NSRP Active/Passive
    • Configuring NSRP Active/Active, VSD-Less Cluster, and NSRP-Lite
    • Tuning Failover Performance
    • VRRP Support
    • Redundant Interfaces
    • Demo: NSRP
  • Section 9 : Traffic Management
    Lessons
    • Need for Traffic Management
    • Egress Traffic Shaping
    • Ingress Policing
    • DSCP Marking
  • Section 10 : Appendix A: Virtual Systems Variations
    Lessons
    • Vsys with IP Classification
    • Transparent Mode Vsys